BLOCKsignalling CDU2RL CDU2 with Ready Led on lead

BLOCKsignalling Show reviews

Availability: In Stock Out Of Stock
Code: BLOCDU2RL

£14.99 £0.00
Earn 14 Rewards Points

Want to be notified when this product is back in stock? Complete the form below and we'll send you an email when it is.


Capacitor Discharge Units of Various Capacities for all sizes of Layout BLOCKsignalling CDUs provide a high current pulse to operate points motors Protects against coil burn-out by limiting subsequent current Regulates charging current to prevent voltage fluctuations on the rest of the layout Recharging time typically 0.8 seconds Various sizes to suit all sizes of layout Versions available with Ready Led to indicate charge state Model railways which use points primarily use points motors which creates a linear movement of about 5mm (1/4in) of the blades of the points. To create this movement, the simplest device is the solenoid which consists of a coil of wire wound on a former. Inside the former is an iron actuator or slug which can be pulled into the coil when the power is applied. By placing two of these coils end-to-end, a forward and reverse motion can be created. These two-solenoid point-motors are usually switched by short pulses of electricity. The pulse length is often determined by the operator or by a simple spring-loaded switch. There are several problems with this arrangement. Point motors require a considerable amount of current for their operation. This means the full capacity of the transformer will be needed and any other items using the same supply may suffer voltage drop during the coil operation. The high currents can also damage switches. The back emf (reverse voltage) generated by the solenoid is sometimes sufficient to cause sparks and can contaminate the switch contacts that, after a time, can weld the switch closed. This will keep the current flowing through the solenoid and it will overheat very quickly. A Capacitor Discharge Unit (CDU) overcomes all these problems. CDUs supply a high current to the solenoid. This current burst is over by the time the switch contacts open, thus eliminating back emf across the switch contacts. Should a solenoid be left in circuit by the switch being held for a long period, the current flowing through the coil (after the initial surge) will be less than 50mA so it will not damage to the coil.


Made by: BLOCKsignalling
Supplier Code: CDU2RL
Availability: Last Chance
BLOCKsignalling Hide reviews

Customer reviews

Leave a review

 

You may also like

Busch 7198 OO/HO/TT Pothole Repairs

£8.70

Busch 8715 Trailer ladder

£24.90

Busch 1150 Toad migration area signs and barricades with toads

£13.70
Tillig 08858 Interior Lighting

Tillig 08858 Interior Lighting

£30.90

Busch 1392 Large Building

£50.50

Busch 1516 Breeding stable

£29.90
Busch 7779 Slurry pump with hoses

Busch 7779 Slurry pump with hoses

£5.90
Busch 1181 Winter Snow Equipment

Busch 1181 Winter Snow Equipment

£16.40

Kibri 13573 KAELBLE Tractor Unit Deutsche Bundesbahn

£19.50

Busch 1069 Maypole

£18.40

Busch 1659 OO/HO Barn Treasures

£32.90

Kibri 26253 Low side car loaded with cabs

£64.00
Busch 1657 Residential house with extension

Busch 1657 Residential house with extension

£65.90

Kibri 14646 DAF tractor with box semi-trailer

£14.90

Busch 1655 Farmhouse

£71.40

Busch 1491 Milestones

£10.90

Tillig 8414 Switching relais

£31.70

Busch 1548 Commercial building

£47.90

StarTec 10672 Stencil cutting tip for 10605

£9.70
Busch 7906 Vehicle with crane and construction workers

Busch 7906 Vehicle with crane and construction workers

£26.99

The item has been added to your basket

Continue Shopping
Proceed To Checkout

This website is Copyright © 2021 Golden Valley Hobbies Limited. All Rights Reserved.

  • Paypal
  • Mastercard
  • Visa
  • JCB
  • Maestro
  • Payment gateway